Arduino Measuring System & Software

$30-250 AUD

Ditutup

Dibuat

sekitar 8 tahun yang lalu

$30-250 AUD

Dibayar ketika dikirim

I currently have a PLC that i would like to replace. The current PLC and software solution is used in combination to control an electric motor in both the forwards and reverse operation. The PLC has inputs from the incremental encoder and proximity sensor. Basically a target length is entered into the system and the motor starts - Once the target length is achieved the motor stops. I have an incremental encoder 1000 pulses per revolution. 200mm circumference wheel. Currently the motor over runs the target once it is switched off. I would like to reduce this with some sort of offset on the target length. I would like to replace the PLC and software with an arduino & relays to control the motor. I imagine that the arduino will be more of a communication device between the PC or Tablet and the electric motor. The majority of this task will be programming. I would like to control this via bluetooth if usb is easier then i will run with that for now. This is more of a prototype. just the basics at this stage. Im guessing someone multi-skilled in both software and hardware will be needed. Someone with experience please I have a sketch appears to work well with the encoder. Im really after someone who knows what they are doing!! Please do not apply unless you are 100% sure you can complete the project. I am wanting someone who can make an immediate start! Is anyone able to help me out?

ID Proyek: 10292042

Tentang proyek

26 proposal

Proyek remot

Aktif 8 tahun yang lalu

Ingin menghasilkan uang?

Alamat email

Keuntungan menawar di Freelancer

Tentukan anggaran dan garis waktu Anda

Dapatkan bayaran atas pekerjaan Anda

Uraikan proposal Anda

Gratis mendaftar dan menawar pekerjaan

26 freelancer menawar dengan rata-rata $204 AUD untuk pekerjaan ini

@ahmedmohamed85

Dear sir I have more than 9 years experience in electronic design please check my profile also please message me so that we can discuss Best regards

$333 AUD dalam 4 hari

4,9

(213 ulasan)

7,4

@mechatronicsengr

Hi, I hope you are doing well. I have read your project. I would like to discuss it in more details. Looking Forward, Khawaja

$147 AUD dalam 3 hari

4,8

(96 ulasan)

7,0

@Anthony989

Hello, I am Anthony. I am working FULL TIME as freelancer. I have double degrees in Mechatronics and Applied Science fields. I have very good feedbacks on freelancer.com . Please check the link at the end and review my feedbacks. So you can get an idea of my work. I have the capability to guide you until the manufacturing stage. I have many contacts in China and can help you to setup there if you are gonna mass produce your product. https://www.freelancer.com/u/Anthony989.html Thank you Anthony

$155 AUD dalam 3 hari

4,9

(65 ulasan)

6,5

@microembedded

hi i am an electrical engineer. i have vast experience regarding micro controllers and their programing. i have worked on many embedded systems. i have worked on many projects regarding motor control. i can do this project for you. let me know if you are interested. we can discuss further on chat.

$500 AUD dalam 3 hari

4,9

(20 ulasan)

6,2

@oobretenov

What kind of PLC you have now. What kind of encoder you have . Now the motor has ON/OFF control only? You need just one offset - The PLC also could communicate with PC . I could help you with arduino , but you have to be sure what you need and what you will reach.

$277 AUD dalam 3 hari

5,0

(43 ulasan)

6,1

@tuan10clc

Hello. I am expert in PLC/SCADA/Arduino. I have reviewed your project carefully. I think you should use PLC S7-1200 for your project because: - S7-1200 has 2 high speed counter able receive pulse encoder. - S7-1200 has 2 analog inputs able receive signal proximity sensor. - Can do a website on S7-1200, so that you can access this website from any device to monitor/control your system. - Easy for install, power, wiring, program. - Low price I program in S7-1200 for $155. Time: About 4-6 days Thanks.

$155 AUD dalam 6 hari

5,0

(20 ulasan)

5,1

@gauravsharma132

Dear Friend, We have good experience in embedded software and design, It is not only our job but passion. We have worked on from basic hardware to quad-copters. Also have lot of happy and overwhelmed clients, we try to deliver more than expected. We have good command over arduino and sensors/peripherals interfacing. Yes friend it can be done with arduino and can start immediately as per your needs. Do you want to control it via bluetooth or via some PC GUI. We are interested to discuss it further and can do this task as per your satisfaction. Consider us :) Any queries and if u want to see more of our work other than portfolio, Please feel free to ask. Thanks & Have a good day. --- Regards Gaurav Sharma ICF Technologies (P) Ltd ~Excellence is not an act but habit~ Aristotle

$144 AUD dalam 7 hari

4,9

(24 ulasan)

5,0

@andualemtad

I am a PhD student in Robotics area. I have a very good background in Motor control, instrumentation, writing firmware. I have also good experience in Bluetooth serial (SPP) and Bluetooth BLE protocols.

$222 AUD dalam 5 hari

4,3

(4 ulasan)

5,4

@neliosmix

Hi, I have experience with arduino and electronics. I'm sure I can do your project and even give you some suggestions or recommendations. I only have one question now, how do you plan to control it from pc or tablet? Feel free to ask me any questions. Best regards, Nélio Oliveira

$300 AUD dalam 10 hari

5,0

(3 ulasan)

3,7

@ricardopaschoeto

Hi, If you want we have a conversation about your project and/or you if you want i will start with the project analyze and after send some first ideas to you. Best Regards,

$200 AUD dalam 10 hari

5,0

(2 ulasan)

2,8

@hazemhaiba

Hello there , i am a mechatronics engineer with great experience with arduino , i've built a segway and a 3d printer using arduino and plenty of other projects . i know that we can work with PID to reach a better performance and i also want to understand how you would like to communicate with the arduino , a java program , matlab or android app . lets chat :D

$88 AUD dalam 3 hari

5,0

(5 ulasan)

2,0

@vijayraviramkuma

Hi I have very good experience in SCADA/PLC Programmer, Development, Testing in Industrial Automation Fields, and Implementation of Various PLC/SCADA/Embedded based Applications products, If my profile suits for your requirement, please let me know Looking forward to work with you I am ready to do now thanks Ramkumar

$155 AUD dalam 3 hari

0,0

(1 ulasan)

0,0

@kldsdv

I have great experience on arduino developing! I also have many protoypes working good at this time. We can replace that PLC easily !

$155 AUD dalam 6 hari

0,0

(0 ulasan)

0,0

@samith07

I'm new to freelancer. But not to the Software and Automation Industry specially Robotics. I'm confident that I'm capable of implementing any kind of C, C++, Java based software on time as you wish...

$30 AUD dalam 10 hari

0,0

(0 ulasan)

0,0

@enzosanmartin

CEO Eagle Aerospace Tecnologies LLC Jul 2007 - Presente Design and implementation of projects in infraestructure , energy, aerospace,astronomical, industrial The research and consulting in the field of engineering. Business in Texas, USA Write me an email for more information. Thank you very much

$250 AUD dalam 10 hari

0,0

(0 ulasan)

0,0

@ivystephen001

I only a few questions 1) what of motor are you using * a small stepper motor should ideal,if your not using one already 2)can i use MOSFET instead of relays * it would make it much easier to control,with PWM I really would do this for free, bcoz it sound like a fun project but also need to eat

$55 AUD dalam 3 hari

0,0

(0 ulasan)

0,0

@ahsandilawarr11

i am Assistant Technical manager of Sublime Enterprise . i have 5 year experience to work on microcontroller, PLC ,arduino e.t.c , i also design lots of industrial product . Design Pakistan's 1st RFID debit card system for amusement Parks. i can complete your project as you want..

$200 AUD dalam 3 hari