Kayak Monster Dolly

Status: Closed
Hadiah: $300
Entri Diterima: 13
Pemenang: Acaluvneca

Winner

Deskripsi Kontes

This unit is a kayak dolly that allows a kayak to be rolled around. It will attach to the top of the kayak. The frame must be able to rotate within the connection points as this will allow the wheels to be raised and lower by an actuator. below are specifications
Made out of ½ inch steel tubing – Unit will be one piece with one one piece bent to accommodate each angle.
Connectors points: 2 – 3 inch pieces that clamp around the steel tubing to hold it in place. It will have one bolt hole in each corner. It shouldn’t be more the 2 inches wide and 3 inches long and ¼ inch thick. Is should be able to handle 300 lbs of force.
Frame should be 34 inches wide to the middle of the 90 degree bends on each side and 20 inches from the middle of the bend downward
8 inch Plunge casters will be mounted in the end of the downward legs of the unit. These will be held in place with a bolt that runs through the frame and plunge caster insert.
A 1 inch by 2 inch steel tab would a welded on the steel tubing at 90 degrees with the tubing laying flat on the ground. A ¼ inch hole should be drilled in the middle of the hole.

UPDATE: A 16 inch actuator will connect into the tab on the frame and will go to the rear of the frame and will connect to a 14 inch cross member. I need the design in solid works.
The length of the actuator is 16 inches. it goes between the frame and the stabilizing cross rail. When activated it will push the frame moving the wheels up and down.
Thanks for your interest

Keahlian yang Disarankan

Winner

Buat Kontes Seperti Ini

Umpan balik Pemberi kerja

“He’s very responsive and develops and awesome drawing. Will use again”

paislarx12, United States.

Entri teratas dari kontes ini

stevenind Indonesia

0
stevenind Indonesia

0
ARTandFASHION Russian Federation

0
milivoja Serbia

0
alina24032014 Russian Federation

0

Tampilkan Entri Lainnya

Papan Klarifikasi Publik

alina24032014
- 6 tahun yang lalu
Hello! Ready for option number 2. Don't have time to send.
- 6 tahun yang lalu
pankj12345
- 6 tahun yang lalu
#extended
- 6 tahun yang lalu
Yohanesujang
- 6 tahun yang lalu
Please check feedback #17 thx
- 6 tahun yang lalu
Penyelenggara Kontes
- 6 tahun yang lalu
Yes the kayak has a seat and the dolly will bolt on behind it and will be left on the kayak and not be removed.
- 6 tahun yang lalu
1. milivoja
  - 6 tahun yang lalu
  Ok, thank you for your information.
  - 6 tahun yang lalu
milivoja
- 6 tahun yang lalu
Do your kayak have a seat? and do you plan bolting dolly to your kayak before transport.
- 6 tahun yang lalu
Penyelenggara Kontes
- 6 tahun yang lalu
I need the drawings in solid works. Thanks.
- 6 tahun yang lalu
Penyelenggara Kontes
- 6 tahun yang lalu
You can pick the wheels as long as they are 8 inch pnematic
- 6 tahun yang lalu
cgblenderer
- 6 tahun yang lalu
Can the format of the file be Not in Solidworks? Or, are you willing to accept exchange formats?
- 6 tahun yang lalu
arthuralbert
- 6 tahun yang lalu
Hello, Do you have the models for wheels and Actuator or we can pick by ourselves?
- 6 tahun yang lalu
milivoja
- 6 tahun yang lalu
Hi, i will deliver you in few days fully modeled with 3D presentation. Thank you.
- 6 tahun yang lalu
1. milivoja
  - 6 tahun yang lalu
  I hope you will not pick the winner yet
  - 6 tahun yang lalu
Symaths
- 6 tahun yang lalu
Brother apologize I'm interested in your project, I wanted to ask you for what purpose the structure itself is built, and where the kayak will be placed. Do you need 2D CAD drawings with the indicated measurements or a 3D photorealism of how the structure will look?
- 6 tahun yang lalu
Babs3D
- 6 tahun yang lalu
Some of the details are vague. Can you make a side view sketch as well. Maybe a picture of something similar on the market may help too.
- 6 tahun yang lalu
Penyelenggara Kontes
- 6 tahun yang lalu
I have added another drawing and updated the description a bit.
- 6 tahun yang lalu
testevpsa
- 6 tahun yang lalu
Hello Sir, Please, could you detail better the project? Maybe a more explanatory drawing? What is the actuator dimensions?
- 6 tahun yang lalu
stevenind
- 6 tahun yang lalu
im join the result will be send as soon as possible.

Best Regards
Steven
- 6 tahun yang lalu
Penyelenggara Kontes
- 6 tahun yang lalu
The actuator should be horizontal to the frame not vertical. Plunge caster slide into the bottom of the frame. Not bolted from the side. The frame would need radius corners for safety purposes.
- 6 tahun yang lalu
1. cgblenderer
  - 6 tahun yang lalu
  Sir, you should comment on my entry itself.
  - 6 tahun yang lalu
2. cgblenderer
  - 6 tahun yang lalu
  Is the model going to be used for 3D printing?
  - 6 tahun yang lalu
diegome1992
- 6 tahun yang lalu
Hello you could attach another image to understand better the general shape
- 6 tahun yang lalu
1. Penyelenggara Kontes
  - 6 tahun yang lalu
  I will first thing in the morning.
  - 6 tahun yang lalu
Product Designer/CAD/CAM
- 6 tahun yang lalu
Hello. How are you? I am interest in your project. Excuse me, but can you check my profile? If you hire me, then your project will be completed more successfully. Thank you. Regards. Julia
- 6 tahun yang lalu