Design me a wireless, remote controlled LED light or lights
$30-250 USD
Dibayar saat pengiriman
** REPOSTING THIS JOB, WITH A GREATER FOCUS ON THE ELECTRONICS DESIGN AS OPPOSED TO FORM FACTOR**
I'm looking for someone to design an battery-powered array of bright white LED lights (or a single, powerful LED), with the end goal of the electronics fitting in a casing (which I will build based on the electronics) approximately half the dimensions of an iPhone, along with a wireless remote control on/off switch (herein referred to as the "Device").
The Device should be bright enough to be seen clearly from approximately 50 to 75 meters away in dark conditions. The Device will be activated (i.e. turned on and off) via the remote control, with the default switch position being off. The remote control should be approximately the dimensions of an iPod Shuffle (w:4cm x H:4cm x D:0.5cm), with a single, large button on the front, and a tiny, red LED light in the corner to indicate that the button is active. When a user holds down the button on the remote, the light/lights will turn on, and when the button is released, the light/lights turn off (i.e. the lights only come on while the button is being held down by the user, but they cannot remain on without this continuous pressure). The remote and light array should be able to operate wirelessly within a range of approximately 7.5 meters. The batteries should be replaceable and of a type easily available, but long lasting (maybe something like a watch battery, but I'm open to suggestions).
Ideally you'd provide an electronics design/schematic which I could take to a manufacturer, plus have you build a working unit that I can test to see if it operates correctly. The design of the board and lights should fit into the dimensions I outline above (I will work on the plastic casing after I have the electronics done). This should be a very simple circuit to build, so the schematic should be easy to understand.
I will also need to consult with you on material costs. Ideally you could present a few different material options and I choose which group of parts makes the most sense for my needs vs. cost to build (e.g. multiple weaker LEDs vs. a single powerful one).
I can provide detailed drawings of the intended design to whoever this project is awarded to, and help fill in any missing details on how this Device should look and operate.
ID Proyek: #6250256
Tentang proyek
Diberikan kepada:
Hi there! My name is Keith and I am a professional electrical engineer here in the US. I now work solely as a contracting designer and freelancer. I am knowledgable in all sorts of microcontroller implementations, c Lebih banyak
13 freelancer rata-rata menawar $211 untuk pekerjaan ini
I can do for you the desired device, respectively, with a demonstration of work. I have long been engaged in LED display devices. I also find solution for the best wireless control.
Hello Sir, I am an experienced Electronic Engineer with a good previous feedback from my employers. I have four years experience in the field and I would like to work on your project. I h Lebih banyak
Hi, I can do this project for LED base project Following shall be the expected milestones: 1. Specification requirement document. 2. Schematics using Altium 3. Simulation of code and electronics (Where ever poss Lebih banyak
Hi, I'm an electronics engineer with more than 6 years of experience in designing and developing various digital and embedded systems... Currently I help engineering students to complete their academic projects. Lebih banyak
Hi, I have read and understood the project guideline, so you can trust my sincere indulgence both in quality and time frame. I have done similar projects in the past. I will like to use my experience to serve you bet Lebih banyak
Hello, I've worked several time as a freelance designing electronic circuit always thinking in a cost-benefit way. I'm hard working and very skilled in schematic-PCB design. I've worked on wireless applications using Lebih banyak
Hello, I am an Electrical Engineer and in my college I do a lot of projects. I want to do the projecto whit RF or bluetooth. I can disign the circuit.
I have been making robots with arduino and analog electronics since 4 years, now i have started a company that makes robots and digital circuits. I am a circuit hacker and a DIY so i can solve pretty complica Lebih banyak
