Ditutup

Circuit Board Design

I am developing a new electronic puzzle. The puzzle will consist of a 4 inch cubic box. Each face of the box will be a separate challenge.

Face #1: An LED and 9 Push buttons are mounted on this face in a 3x3 grid. When one is pressed, a single LED lights up. When pressure is released, the light goes off. In order to solve this face, all 9 buttons must be pressed simultaneously. When all are pressed at the same time, the LED goes on and stays on until all faces are solved (or the puzzle is reset).

Face #2: This face has two screws and an LED. The LED is only illuminated when the two screw heads are linked by a paper clip (or other metal item). The LED stays on until all faces are solved (or the puzzle is reset).

Face #3: This face has a small hole and and LED. A flashlight must be shined into the hole in order to illuminate the LED. The LED stays on until all faces are solved (or the puzzle is reset).

Face #4: This side has a LED and a speaker sensor that detects loud noises. The player must shout near the speaker in order to illuminate the LED. The LED stays on until all faces are solved (or the puzzle is reset).

Face #5: This face has a LED and a magnetic sensor. The user must place a magnet near the face in order to illuminate the LED. The LED stays on until all faces are solved (or the puzzle is reset).

Face #6: This face doesn't have an LED. The surface is perfectly flat. The final challenge is to trip an accelerometer switch by spinning the box on a table. This activates the last switch for 2 minutes.

When all sides are solved (all LEDs illuminated and accelerometer switch is activated), there is a buzzing sound from an internal speaker and all of the LEDs flash 10 times simultaneously. The puzzle is then reset and all LEDs shut off. I would like it to run on a single AA, or single AAA, or single 9V battery if possible. Each LED and switch automatically goes off after 2 minutes of being on...this is the reset function. Therefore, the puzzle must be solved in less than 2 minutes.

I believe these are all very simple switch circuits. I need a design that is ready to order from a circuit board manufacturer and easy to finish assembly within the box myself. I will need some instruction on parts to order and where to solder wires. The circuit board will be glued to the inside of the box.

Keahlian Teknik Elektro, Elektronika

Lihat lebih lanjut: how to design a circuit board, design pendrive circuit board, board circuit design arm, design barcode circuit using microcontroller, web design change images script, design change products front page oscommerce, circuit diagram power change projcet, virtuemart design change, oscommerce design change, magento design change header, game graphic design board, use simulink design heart circuit, custom banner design board, bid graphic design board, automotive parts website design, graphics design board game development, magento design change, woot design change, average cost graphic design board game, china auto parts website design, freelance design board pcb, design board game program, auto parts website design yearmakemodel, automotive parts website design year models, oscommerce psd design change

Tentang Pemberi kerja:
( 6 ulasan ) Brooklyn, United States

ID Proyek: #12703859

34 freelancer menawar pada rata-rata $564 untuk pekerjaan ini

sagradoamicus

Hi I am an expert electronics engineer with more than 8 years of experience The idea seems interesting I would like to work on it, Please have a look at my profile to see my reputation and do let me know if you are in Lagi

$600 USD dalam 10 hari
(141 Ulasan)
7.1
$750 USD dalam 15 hari
(94 Ulasan)
6.5
geekyexperts

Hello, I am an Electronics and Embedded system developer. I have experience in Digital and Analog electronic design and Matlab.i have expertise in PCB design. My quote include complete design along with the devlopment Lagi

$1200 USD dalam 15 hari
(50 Ulasan)
6.4
Anthony989

Hello Sir/Madam, I am Anthony Perera from Sri Lanka and I have multiple degrees on Engineering field. Why you should hire me ? * I am a FULL TIME freelancer and once a project Lagi

$555 USD dalam 10 hari
(30 Ulasan)
5.8
amelectronics

Hello dear I have experience in designing electronics circuits and can make your project. I will make your project practically on breadboard and will provide you circuit, code and PCB design. I can also develop androi Lagi

$700 USD dalam 15 hari
(12 Ulasan)
4.8
mechatronicsengr

Hi, i hope you are doing well. I have experience in LED based embedded project design and development. I have understood your project requirements and I can execute it in less possible time. Looking Forward, Kha Lagi

$526 USD dalam 10 hari
(9 Ulasan)
4.6
bijan01in

Hi I am interested to your project. I am familiar with electronics, PIC microcotroller as well as PCB design by Eagle. Thanks.

$444 USD dalam 20 hari
(46 Ulasan)
4.9
LeoTheFreelancer

More than 10 years’ experience in Design (R&D), Development (Software) and Project, I am a freelance Consultant/Senior Engineering Business Manager with a team of freelancing/contract/subcontract professionals from all Lagi

$555 USD dalam 10 hari
(6 Ulasan)
4.8
pavanshah2001

hi im embedded systems designer from india. Im experienced with micro-controller based circuit. I can get the required project done as mentioned. I can also help out with part ordering, manufacturing and assembling. I Lagi

$1111 USD dalam 10 hari
(4 Ulasan)
4.6
urasinov

Hi. My bid includes circuit developing, pcb routing with 3D models. Manufacturing and soldering 2 boards. One board for me second for you. Also included EMS fast shipping to you. It is 60 days because I sent one de Lagi

$777 USD dalam 60 hari
(6 Ulasan)
4.2
smartrabbit

Hi! I am Jordan, new one on Freelancer , a CE products and Disney & Marvel characters toys designer from China. I have 10 years of experiences in products design, molding and assembly. I have good knowledge of material Lagi

$736 USD dalam 30 hari
(6 Ulasan)
4.8
ircrashed

Hello I have got your job posting “Circuit Board Design” and I am very much interested to work in your project. I am a circuit designer and have more than 5 years experience of working with the embedded systems(A Lagi

$300 USD dalam 7 hari
(7 Ulasan)
3.8
Chpb3929

Hello, I am interested to work with you on this project. I have read the description and I can do this. Let me know if you are interested. Thanks. Chirag

$355 USD dalam 10 hari
(7 Ulasan)
3.8
boydtvtbk

Dear sir, I'm an electronics engineer with more than 4 years making product for customers around the world. As your project requirements, we can design 6 PCBs that match each Face specs. They will need buttons, reed-sw Lagi

$700 USD dalam 9 hari
(8 Ulasan)
3.9
$555 USD dalam 10 hari
(9 Ulasan)
3.4
$555 USD dalam 10 hari
(6 Ulasan)
3.2
CarlHoffmann

Hi,Client.I am an expert in the electronic fields. I have 13 years experience in circuit, PCB design, and manufacture, firmware and application writting using DSP, VHDL, PLC, STM32, ATmel, PIC, Ardunio, ARM Embedded Lagi

$350 USD dalam 10 hari
(2 Ulasan)
1.7
pin311

Don't worry, We are a professional and I work with Altium, Eagle PCB and Proteus. This circuit for project must has a Microcontroller. There are many Microcontroller. Which microcontroller do you prefer? We work with Lagi

$388 USD dalam 20 hari
(1 Ulasan)
1.1
designproduct

Dear Sir, We can complete the design of electronic puzzle so that you will be able to assemble it putting the least effort. Please message us to clarify any doubts if you have. Best Regards, Prasanth

$250 USD dalam 10 hari
(0 Ulasan)
0.0
MuthusamyLR

I believe these are all very simple switch circuits. I need a design that is ready to order from a circuit board manufacturer and easy to finish assembly within the box myself. I will need some instruction on parts to Lagi

$500 USD dalam 10 hari
(0 Ulasan)
0.0