Demonstrator Code for an TI - CC2530 Chip - TI-Stack

€8-30 EUR

Ditutup

Dibuat

lebih dari 10 tahun yang lalu

€8-30 EUR

Dibayar ketika dikirim

TI\'s new CC2530 is a true system-on-chip solution tailored for IEEE 802.15.4, ZigBee, ZigBee RF4CE and Smart Energy applications. (copy from WEB SIde TI):\r\n\r\nWe need some Demostration SW to show how to write SW for this Chip with OpenSource Tools and/ or TI Composer. \r\n\r\nNeeded is:\r\n\r\nFull setup with OpenSource / TI Composer Studio / IAR (open Source pref.)\r\nDemonstrator Code where on fixed TX-frequency a 64Bit Code is transmitted and then received.\r\nAll Registers and parameters must be fully documented inside the Code.\r\nSchematic of Board will be distributed during discussion.\r\n\r\nExperience with TIs \"SimpliciTI(TM)\" Network Protocol for Sub-1 GHz, 2.4 GHz and IEEE 802.15.4 RF ICs \r\nand/or REMO TI and/or Z-Stack(TM) is welcome.

ID Proyek: 4407594

Tentang proyek

7 proposal

Proyek remot

Aktif 10 tahun yang lalu

Ingin menghasilkan uang?

Alamat email

Keuntungan menawar di Freelancer

Tentukan anggaran dan garis waktu Anda

Dapatkan bayaran atas pekerjaan Anda

Uraikan proposal Anda

Gratis mendaftar dan menawar pekerjaan

7 freelancer menawar dengan rata-rata €106 EUR untuk pekerjaan ini

@scribblerspk

I can do this project, I have 12 years of design n development experience. You can review my profile and reviews. Thanks.

€210 EUR dalam 20 hari

4,8

(8 ulasan)

5,1

@betaenergy

Dear Sir, We are Reserach and Development company whose working area are : -Digital Motor Control -Analog Design -Electronic Design -Power Electronics -PCB design -Embedded system -Matlab -Simulation of hardware For each concept descriptions are as follows: Digital Motor Control: -3-phase induction motor vector control drive -Flux estimation algoritm generation -DSP(TMS320) implementation on motor drive -Low speed application -Torque and speed loop generation -Control algoritms Analog design -Low power distribution -Noissless special opamp based analog circuits -Analog filters -Orcad simulation of several circuits Electronic Design -RF transmitter and receiver -Bluetooh reader and transmitter -Magnetic reader Power Electronics -Implementation motor drive -AC/DC converter -DC-DC converter -Battery charger -Solar inverter -Renewable Energy simulations -Uninterruptle power supplies PCB design -Schematic design by Altium -PCB design by Altium -Power board design -SMPS board design Embedded system -PIC18,PIC24,PIC30 and dsPIC applications -Ardino -MSP430 -Atmel -DSP(Texas Instruments) -Renesas Matlab -Power Electronics simulation -Motor drive -Wind Energy -Solar Energy -Control applications Simulation of Hardware -Orcad Simulation(TI,National, Linear Tech, Maxim libraries) -LTI -National -Matlab Very important Note: References attached. Please look excel file to see projects which we made until now! Metin

€78 EUR dalam 3 hari

4,6

(13 ulasan)

4,7

@RaciSolutions

Hello! I am a computer science student and I am very interested in your project. I have worked before with SimpliciTi stack on CC1100 and CC2500 modules and I think I have enough experience to help you. If you are interested in some kind of demo based on TI examples, please let me know. Thank you and have a nice day! RaciSolutions.

€111 EUR dalam 3 hari

5,0

(1 ulasan)

1,1

@xtintt

Hi, I am firmware programmer. I can help you in setup of CCS or IAR Embedded workbench setup. Let me know if interested. Dhaval

€111 EUR dalam 3 hari

0,0

(1 ulasan)

3,1

@newgandharva

Have worked (and currently working) on TI's CC2530 SoC, development platform used is CC2530EM from TI, using IAR EW8051 as the IDE for development. Have implemented TI's proprietary SimpliciTI protocol and Z-Stack (TI's open-source ZigBee stack) on the same. Ready to start working.

€34 EUR dalam 3 hari

0,0

(0 ulasan)

0,0

@mohanatta

I have a experience on the ti wireless IC's like cc2500 cc1100 and cc2480 . i am familiar with the ti tools to be used. can deliver the high and easily understandable code with full comments about the action of each register. My understanding of your requirement : All you need to transfer 64bytes of data and receive 64 bytes of data. My plan : Document about each registers functionality in detail and how to use it in the code. and implementing it in code for 64 bytes of data to transfer and receive and show the demo.

€22 EUR dalam 3 hari