Nirkabel Jobs

I have a Ubiquiti Unifi network and need some assistance, happy to pay for consultation time

Hi, I need to program the LILYgo 7000G board to communicate via MQTT via LTE and wifi. It is also required to read the GPS position. Regarding the power part, it is necessary that the board goes into deep sleep consuming in general less than 50 ua/hour. To achieve that it should be possible to turn off the SIM7000G via software through the ESP32 and put the ESP32 into deep sleep. It would be necessary to see the rest of the electronic components and their power consumption.

Please the details before do the bid We are looking for a talented machine learning engineer to help us reduce the size of our EleutherAI/gpt-neox-20b and EleutherAI/gpt-j-6B and similar models using an MP method. The successful candidate will be responsible for designing and implementing an MP module to reduce the RAM requirements of these models, while maintaining their performance. Responsibilities: Develop and implement an MP module to reduce the RAM requirements of the EleutherAI/gpt-neox-20b and EleutherAI/gpt-j-6B models Work closely with the research team to ensure that the MP module does not significantly impact the models' performance Optimize the MP module to achieve maximum reduction in RAM usage while maintaining performance Document the MP module design and implement...

Looking for a program or software to intercept my current EEG wireless body area network I don't have much details about the current one I'm using but looking to intercept the physical part

Hello there, We are looking for a talented machine learning engineer to help us reduce the size of our EleutherAI/gpt-neox-20b and EleutherAI/gpt-j-6B and similar models using an MP method. The successful candidate will be responsible for designing and implementing an MP module to reduce the RAM requirements of these models, while maintaining their performance. Responsibilities: Develop and implement an MP module to reduce the RAM requirements of the EleutherAI/gpt-neox-20b and EleutherAI/gpt-j-6B models Work closely with the research team to ensure that the MP module does not significantly impact the models' performance Optimize the MP module to achieve maximum reduction in RAM usage while maintaining performance Document the MP module design and implementation for future referenc...

We are an antennas manufacturing company, and our website has about 800 pages of product pages and another 200 pages in our technical blog. We need a technical writer who can do the following ongoing projects as a part-time job that will continue for many years into the future. You do not have to have skills in HTML, CSS, web-page editing/formatting etc, for this position, because we have an employee who can do that aspect (if you are a technical writer with relevant knowledge in wireless/antennas etc, that does not have the web-page editing skills, that is not any problem: We need the technical writing aspect of your skills as we have someone with the web-page formatting skills). 1. Review older articles on our blog, that have dated information, and update and/or "refresh the co...

I want to be able to connect to the Electric Control Module (ECM) on a tour bus or tractor trailer remotely to the 1939 can line (communication line). We have multiple software we use to connect to the different computers on the vehicles. I run Samsara ELD's, Peoplenet ELD, and have Cradlepoint IBR 900 routers onboard. I want to be able to run Cummins Insite mainly, but also Meritor ACOMM, Wabco Toolbox, and Allison DOC. I want to be able to pull up the diagnostic software in my office and connect to a vehicle. I want to be able to run tests, as well as erase faults, and recalibrate the ECM. Is this possible?

The project is based on underground fault detection over IOT. The block diagram and the research paper is attached below.

I am looking for an experienced Arduino developer to work on a project that involves controlling a 1-meter RGB LED strip, creating & communicating via a wireless mesh network using Arduino Nano V3.0 ATmega328P & XBee modules. I need someone to guide me in setting up a mesh network with multiple nodes - a maximum of 12 or 16 nodes. I will do the doing - but I need your instruction as a tutor & to teach me how it's done. The ideal candidate should understand Arduino Uno & Nano boards, XBee modules, WS2812B or NeoPixel RGB LED strips, & Bluetooth or Wi-Fi modules. Responsibilities: Guide the development & implementation of a reliable & secure wireless communication system between Arduinos & cell phones using XBee modules. I am still determining whether t...

Trying to connect gaming console via ethernet cable, but running into problems. Also cannot connect to router IP: err_connection_refused. Just looking to maximize speed and reduce ping for online gaming.

Hello I need someone with expertise in Network Simulation who can create a small simulation for me of any router in Kathara or any other open source software. Do not copy paste cover letters

We are seeking a highly skilled Network Engineer with CCNA certification to join our team. The ideal candidate will have a solid understanding of network architecture and protocols, including LAN, WAN, and wireless technologies. Responsibilities: • Design, deploy, configure, and maintain network infrastructure, including LAN, WAN, VPN, and wireless technologies. • Monitor and optimize network performance, capacity, and security. • Troubleshoot network issues and resolve them quickly and efficiently. • Collaborate with other IT teams to develop and implement network solutions that align with business requirements. • Participate in on-call rotation for after-hours support and maintenance. • Create and maintain network documentation, includin...